INNER RING TOLERANCE — ABEC 7P — ABEC 5P, VALUES ARE IN .0001"

BORE DIAMETER				BORE TOLERANCE +0		RADIAL RUNOUT (MAX.)		WIDTH VARIATION (MAX.)		REFERENCE RUNOUT WITH BORE (MAX.)
MM OVER	MM INCL.	INCH OVER	INCH INCL.	APEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P
0	10	0	0.3937	-1.5	-2	1	1.5	1	2	1	3
10	18	0.3937	0.7087	-1.5	-2	1	1.5	1	2	1	3
18	30	0.7087	1.1811	-1.5	-2	1.5	1.5	1	2	1.5	3
30	50	1.1811	1.9685	-2	-2	1.5	2	1	2	1.5	3
50	80	1.9865	3.1496	-2	-3	1.5	2	1.5	2	2	3
80	120	3.1496	4.7244	-2.5	-3	2	2.5	1.5	3	2	3

INNER RING TOLERANCES — ABEC 5P AND ABEC 7P

GROOVE RUNOUT WIDTH REFERENCE SIDE (MAX.)		WIDTH TOLERANCES +0		BORE 2-POINT OUT-OF-ROUND (MAX.)		BORE TAPER (MAX.)
ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P
1	3	-10	-10	1	1	1	1
1	3	-10	-10	1	1	1	1
1.5	3	-10	-10	1	1	1	1
1.5	3	-10	-10
1.5	3	-10	-15
2	4	-15	-15

OUTER RING TOLERANCE — ABEC 3 — ABEC 1 VALUES ARE IN .0001"

OUTER DIAMETER				OUTER DIAMETER TOLERANCE LIMIT +0		RADIAL RUNOUT		WIDTH TOLERANCES +0		FLANGE WIDTH TOLERANCE LIMITS +0		FLANGE DIAMETER TOLERANCE LIMITS +50
MM		INCH		ABEC 3	ABEC 1	ABEC 3	ABEC 1	ABEC 3	ABEC 1	ABEC 3	ABEC 1	ABEC 3	ABEC 1
OVER	INCL.	OVER	INCL.
0	18	0	0.7087	-3	-3	3	6	-47	-47	0	-47(2)	+106(1)	-17(1)
18	30	0.7087	1.1811	-3	-3.5	4	6	-47	-47	0	-47	+130	-20
30	50	1.1811	1.9685	-3.5	-4.5	4	8	-47	-47	0	-47	+154	-24
50	80	1.9685	3.1496	-4.5	-5	5	10	-47	-47	0	-47	+181	-29
80	120	3.1496	4.7244	-5	-6	7	14	-59	-59	0	-47	+213	-34
120	150	4.7244	5.9055	-6	-7	8	16	-79	-79

(1) 0-10mm bore, High=+87, Low=-14    (2) 0-10mm, Low=-16

OUTER RING TOLERANCE — ABEC 7P — ABEC 5P, VALUES ARE IN .0001"

OUTER DIAMETER				OUTER DIAMETER TOLERANCE +0		RADIAL RUNOUT (MAX.)		WIDTH VARIATION (MAX.)		OUTSIDE CYLINDRICAL SURFACE RUNOUT WITH REFERENCE SIDE (MAX.)
MM OVER	MM INCL.	INCH OVER	INCH INCL.	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P
0	18	0	0.7087	-2	-2	1.5	2	1	2	1.5	3
18	30	0.7087	1.1811	-2	-2	1.5	2	1	2	1.5	3
30	50	1.1811	1.9685	-2	-2	2	2	1	2	1.5	3
50	80	1.9685	3.1496	-2	-3	2	3	1	2	1.5	3
80	120	3.1496	4.7244	-3	-3	2	4	2	3	2	3
120	150	4.7244	5.9055	-4	-4	3	4	3	3	2	4

OUTER RING TOLERANCES — ABEC 5P AND ABEC 7P

GROOVE RUNOUT WIDTH REFERENCE SIDE (MAX.)		WIDTH TOLERANCES +0		FLANGE WIDTH TOLERANCE LIMITS +0		FLANGE DIAMETER TOLERANCE LIMITS +0		OUTER DIAMETER 2 POINT OUT-OF-ROUND (MAX.)		OUTER DIAMETER TAPER (MAX.)
ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P	ABEC 7P	ABEC 5P
2	3	-10	-10	-20	-20	-10	-10	1	1	1	1
2	3	-10	-10	-20	-20	-10	-10	1	1	1	1
2	3	-10	-10	-20	-20	-10	-10	1	1	1	1
2	4	-10	-15
2	5	-15	-15
3	5	-15	-15